Căutare
Search
717 results were found.
De ce șindrilele IKO reprezintă cea mai bună opțiune pentru acoperișul dvs.?
Aprofundați mai multe informații despre șindrilele Cambridge
Soluția ideală pentru ...
- Acoperișurile cu pantă redusă din OSB: pe acoperișurile cu panta cuprinsă între 4° și 15° membrana Armourbase Thermo AD se montează paralel cu streașina fără fixări mecanice în zona de suprapunere.
- Strat support din beton: aplicare paralel cu streașina fără fixare mecanică pe acoperișuri cu pantă cuprinsă între 4° și 15°. Pentru pante mai mari (max. 45°), aplicarea se face perpendicular pe linia de streașină cu fixare mecanică obligatorie în zona de suprapunere (șuruburi cu talere de fixare).
- Termoizolație peste substrat din beton sau OSB cu panta acoperișului(min. 4°- max. 15°): Termoizolația trebuie să fie aplicată cu fixări mecanice de stratul suport, beton sau OSB, doar dacă panta acoperișului este cuprinsă între 4° și 15°. În astfel de situații membrana Armourbase Thermo AD trebuie să fie fixată mecanic în dreptul suprapunerilor datorită aderenței limitate la materialul termoizolant.
- Renovarea acoperișurilor existente (> 4°): (doar daca stratul suport este uscat, curat și impermeabil) Primer AD + fixările mecanice sunt indispensabile pentru montajul membranei.
How to apply the torch on system?
Application of the underlayment on a wooden deck
Apply the membrane parallel with the eaves - vertical and horizontal overlaps should be min. 10 cm. Set the roll of Armourbase Thermo AD and remove the release film from the back. In warm, sunny weather the underlayment will stick with the wooden deck in a short time.
For slopes between 4° - 15° it is not necessary to fix the underlayment on overlaps. It is advisable to go with proper metal flashings at the eaves and rakes.
Provide horizontal and vertical overlaps 10 cm between the sheets and make sure to remove the side selvedge release foil. After application use a suitable roller and apply pressure over all overlaps.
The adhesion of Armourbase Thermo AD will start with the application of bituminous shingles by torch-on.
Application of the underlayment on a concrete deck
Apply the membrane parallel with the eaves - vertical and horizontal overlaps should be min. 10 cm. The position of Armourbase Thermo AD on the concrete deck with slopes higher than 15° should be perpendicular to the eaves.
The concrete deck must be primed with the Primer AD (bituminous primer) before the application. Set the roll of Armourbase Thermo AD and remove the release film from the back. In warm, sunny weather the underlayment will stick with the primed concrete deck in a short time. In cold weather you can help to set the Armourbase Thermo AD underlayment with a hot air gun or a torch.
For slopes between 4° - 15° it is not necessary to fix the underlayment on overlaps. For concrete decks with slopes between 15° - 45°, fixation is mandatory. This can be ensured with screws and metal pressure plates for concrete. There is a need to pre-drill holes every 30 cm on overlaps. It is advisable to go with proper metal flashings at the eaves and rakes. Provide horizontal and vertical overlaps 10 cm between the sheets and make sure to remove the side selvedge release foil. After application use a suitable roller and apply pressure over all overlaps.
The adhesion of Armourbase Thermo AD will start with the application of bituminous shingles by torch-on.
Horizontal "Armourbase Thermo AD" application on low sloped concrete deck (4°-15°)
Vertical "Armourbase Thermo AD" application on concrete deck (15°-45°) with mechanical fixing
Horizontal "Armourbase Thermo AD" application on low sloped concrete deck (4°-15°)
Vertical "Armourbase Thermo AD" application on concrete deck (15°-45°) with mechanical fixing
Contact us for more information on the Armourbase Thermo AD torch on membrane system